Por favor, use este identificador para citar o enlazar a este item:
http://hdl.handle.net/10261/287706
COMPARTIR / EXPORTAR:
SHARE CORE BASE | |
Visualizar otros formatos: MARC | Dublin Core | RDF | ORE | MODS | METS | DIDL | DATACITE | |
Título: | Optimisation of the processing conditions of hydrolytic hydrogenation of cellulose using carbon nanofiber supported Ni catalysts |
Autor: | Frecha, Esther CSIC; Remón, Javier CSIC ORCID; Torres Gamarra, Daniel CSIC ORCID; Suelves Laiglesia, Isabel CSIC ORCID ; Pinilla Ibarz, José Luis CSIC ORCID | Palabras clave: | Cellulose Hydrolytic hydrogenation Carbon supported catalysts Nickel Sorbitol |
Fecha de publicación: | 13-ene-2023 | Editor: | Elsevier BV | Citación: | Catalysis Today 423: 114002 (2023) | Resumen: | The synthesis of sorbitol from cellulose over Ni catalysts is a promising valorisation route in the biorefinery scenario, applying relatively simple preparation methods and earth-abundant metals. The overall selectivity, however, depends on the kinetic control of a complex reaction network, involving the hydrolysis of cellulose to monosaccharides via cello-oligomers, glucose hydrogenation into sorbitol and hydrogenolysis side-reactions of sugars and sorbitol to low molecular weight polyols. Therein, subtle changes in the catalyst composition and process conditions might have a strong impact on the final product distribution. Driven by these challenges, this work first-time provides novel insights into the hydrothermal hydrogenation of cellulose over a carbon nanofibre supported Ni catalyst (Ni/CNF). Firstly, the impact of the duration of a ball-milling pre-treatment step and the influences of the hydrothermal time and temperature were thoroughly analysed. The experimental results obtained highlighted the importance of process control to promote the first transformation of cellulose to glucose and its subsequent hydrogenation to sorbitol to minimise the extension of side reactions. Finally, an additional study was conducted to palliate the recalcitrant nature of cellulose by decreasing mass transfer limitations to a minimum extent. This was achieved by including an additional mix-milling of the amorphous cellulose produced in the first pre-treatment with the catalyst and increasing the H2 pressure of the hydrothermal hydrogenation process. This allowed attaining a sorbitol yield as high as 62% at 190 ºC using an initial H2 pressure of 8 MPa for 26 h, which is one of the best results reported in the literature. | Descripción: | 14 figures, 6 tables. | Versión del editor: | http://dx.doi.org/10.1016/j.cattod.2023.01.009 | URI: | http://hdl.handle.net/10261/287706 | DOI: | 10.1016/j.cattod.2023.01.009 | ISSN: | 0920-5861 | E-ISSN: | 1873-4308 |
Aparece en las colecciones: | (ICB) Artículos |
Ficheros en este ítem:
Fichero | Descripción | Tamaño | Formato | |
---|---|---|---|---|
1-s2.0-S0920586123000093-main.pdf | 4,98 MB | Adobe PDF | Visualizar/Abrir |
CORE Recommender
SCOPUSTM
Citations
2
checked on 07-may-2024
WEB OF SCIENCETM
Citations
2
checked on 24-feb-2024
Page view(s)
43
checked on 15-may-2024
Download(s)
1
checked on 15-may-2024
Google ScholarTM
Check
Altmetric
Altmetric
Este item está licenciado bajo una Licencia Creative Commons